87 lines
3.9 KiB
Markdown
87 lines
3.9 KiB
Markdown
+++
|
|
date = "2017-11-13"
|
|
title = "Repair: Rotel RB-970BX"
|
|
tags = ["rotel", "repair", "audiorepair"]
|
|
categories = [ "Audio Repair" ]
|
|
description = "Another lucky find: Rotel RB-970BX Power Amplifier with one defective channel. Let's fix this!"
|
|
slug = "repair-rotel-rb-970bx"
|
|
+++
|
|
|
|
![The Rotel RB-970BX](/img/rotel-rb970bx-front.jpg)
|
|
|
|
I did another great find on _Marktplaats_: a Rotel RB-970BX. This is a power amplifier, meaning it has no
|
|
volume or tone controls whatsoever. You'd normally pair a RC-970BX pre-amp with one or two of these
|
|
power amplifiers.
|
|
|
|
The amp can operate in _stereo_ at 60W per channel or in _bridged mono_ for up to 180W of power. In bridged
|
|
mono you can use the entire amp to amplify either the left or right channel to a single speaker. Of course,
|
|
for stereo, you'd need two of these amplifiers in your setup.
|
|
|
|
![Bridged Mono on the RB-970BX](/img/rotel-rb970bx-bridged-mono.png)
|
|
|
|
## Diagnostic
|
|
|
|
I bought this amp with the remark that one channel did no longer produce any sound. This Rotel
|
|
amp was a complete unknown to me, but my guess was it'd be easy enough to fix.
|
|
|
|
![The insides of the RB-970BX](/img/rotel-rb970bx-pcb.jpg)
|
|
|
|
Before powering up an unknown device I always take of the cover and do a visual inspection.
|
|
This amp looks really clean and lightweight. There's not a single IC in there! I checked for
|
|
any obvious failures, like buldging capacitors, fried resistors or burn marks on the PCB.
|
|
Nothing looks out of ordinary, so that means there's a possible issue with any one of the
|
|
transistors on the board.
|
|
|
|
The power transistors, those mounted on the heatsinks, are prime candidates for failure due
|
|
to the thermal stress they get. With my multimeter I did a quick continuity test to see if
|
|
any of these were shorted out - all appear to be fine.
|
|
|
|
Another quick test I performed is verifying the bias resistors (the large white ones). These
|
|
are high power, low resistance. All measured in spec at around 0.22Ω - so no open
|
|
or short circuits there either.
|
|
|
|
Next I powered up the amp for the first time - with nothing connected to it. I measured
|
|
for DC on the outputs but both were in the mV range. Right was close to 0V whereas the
|
|
left channel had a few mV of DC. Might be nothing, might be something.
|
|
|
|
Next I hooked up a dummy load (8Ω 200W in power resistors) and applied a 1kHz sine
|
|
wave to the input. With my oscilloscope I quickly determined that the right channel was
|
|
in working order. Left was out completely.
|
|
|
|
Since I already checked the major culprits of a dead channel, I continued to check the
|
|
other transistors on the left channel circuit. The first one I tested (Q615, a 2SC2910
|
|
NPN transisor) showed a short between _emitter_ and _base_.
|
|
|
|
A quick probe around showed no other damaged parts. Resistors showed their correct values
|
|
or I would get values that indicate a capacitor getting charged. All other transistors
|
|
checked out ok as well.
|
|
|
|
After taking out Q615 I put it in my component tester and instead of an NPN transistor, it
|
|
showed up as two diodes.
|
|
|
|
![Defective NPN transistor 615](/img/rotel-rb970bx-npn-defect.jpg)
|
|
|
|
This is what a working 2SC2910 transistors looks like on my tester:
|
|
|
|
![Replacemenet NPN transistor](/img/rotel-rb970bx-npn-okay.jpg)
|
|
|
|
## The Repair
|
|
|
|
The shorted transistors was quickly replaced (a local supplier has the exact model in stock).
|
|
This model has a removable bottom panel that gives easy access to the bottom of the PCB.
|
|
|
|
![Bottom view during repair](/img/rotel-rb970bx-bottom-repair-annotated.jpg)
|
|
|
|
While I had the unit opened up on my bench I also to the opportunity to clean the insides using
|
|
some rubbing alcohol and compressed air.
|
|
|
|
After verifying correct operation with a dummy load and my scope I hooked up pair of speakers and
|
|
got to enjoy the beautiful sound of this Rotel amp.
|
|
|
|
## One more thing
|
|
|
|
<div class="pollly-embed" data-id="LeOA6N3R"></div><script src="https://poll.ly/scripts/embed.js"></script>
|
|
|
|
## Links
|
|
|
|
[Rotel RB-970BX Datasheet at Hifiengine](https://www.hifiengine.com/manual_library/rotel/rb-970.shtml) |