101 lines
4.5 KiB
Markdown
101 lines
4.5 KiB
Markdown
+++
|
|
date = "2018-09-12"
|
|
title = "Design: Phono X, a RIAA Phono Preamplifier"
|
|
tags = ["design", "audio", "preamp", "phono"]
|
|
categories = ["Audio Design"]
|
|
summary = "Building a quality phono preamp is still one of the joys of the audio electronics enthusiast. This is my first take on a RIAA phono premap."
|
|
aliases = [
|
|
"/2018/09/12/phono-x-riaa-phono-preamp/"
|
|
]
|
|
+++
|
|
|
|
![Featured](featured.jpg)
|
|
|
|
When I started out designing this preamp I only had a few requirements:
|
|
|
|
* Perform RIAA equalisation and pre amplification for a Moving Magnet (MM) cartridge
|
|
* Connect my [Technics SL-3310](https://www.vinylengine.com/library/technics/sl-3310.shtml)
|
|
to my [Denon AVR-2113](https://www.denon.co.uk/uk/product/homecinema/avreceiver/avr2113).
|
|
* Sound decent (e.g. no 50 Hz hum, etc.)
|
|
* Directly powered from 230VAC
|
|
|
|
Searching the internet yielded quite a few pre-designed phono preamp stages. The main
|
|
issue I had with most of them is the sheer amount of customization put into each design.
|
|
Take the [Muffsy](https://www.muffsy.com/schematics.html) for example. The Muffsy tries to
|
|
accomodate many different cartridges by making input impedance and gain configurable. This
|
|
is great, but I just have _one_ turn table. I might get another one in the future, but I'm
|
|
pretty sure it's going to be mainstream moving magnet again.
|
|
|
|
I also found [Elliot Sound Products' Project 06](http://sound.whsites.net/project06.htm
|
|
), a Hi-Fi Phono Preamp with RIAA equalisation and good reviews.
|
|
|
|
With all the different designs in the back of my mind, I started out designing Phono X.
|
|
|
|
## The power supply
|
|
|
|
The power supply is normally the last thing I design. When everything else is finished, I have
|
|
a clear picture of power supply needs. Because the main components are a pair of [OPA2134] opamps,
|
|
I want to have a clean ±15VDC power supply. The OPA2134 can be supplied with up to ±18VDC, but
|
|
±15VDC seems more than adequate for the job. ±15VDC is also what Elliot recommends in his design.
|
|
|
|
So, to get a clean supply voltage, I opted for an almost classic linear power supply, using a
|
|
20VA 2x 15VAC toroidal transfomer.
|
|
|
|
![](/images/audio/phono-x/schematic-power-supply.png)
|
|
|
|
`AC1` and `AC2` are connected to the transformer. The `D1-D4` diode bridge rectifies the AC
|
|
into DC which gets filtered by the capacitors `C1-C4`. Next is a +/- pair of an LM317 and LM337
|
|
to regulate the voltage to ±15VDC, including protection diodes.
|
|
|
|
## Pre-amp circuit
|
|
|
|
Below is left channel preamp circuit, the right channel is identical. Most notable detail is
|
|
the OPA2134, which is a dual channel opamp. One unit is used for L+R RIAA equalisation and
|
|
another unit is used for amplification.
|
|
|
|
This is almost an exact copy of Elliot Sound Products' Project 06 design with a few small
|
|
tweaks.
|
|
|
|
![](/images/audio/phono-x/schematic-left-channel.png)
|
|
|
|
* I omitted the `CLL` and `CRR` cartridge loading capactiors.
|
|
* For `C19` and `R22` I used 100nF and 750Ω instead of the specified 82nF and 820Ω, as per ESP's instructions.
|
|
* The 10uF and 100nF by pass capacitors for the opamps are omitted in favour of `C15-C17` in
|
|
the power supply.
|
|
|
|
## PCB Design
|
|
|
|
This is the final PCB design. In retrospect I should have better divided the available
|
|
board space between different functions. Power supply and preamp are a bit mixed up. Also,
|
|
the signal traces for the right channel are tad longer than left. I'm not sure this results
|
|
in an audible difference, but it still doesn't feel right.
|
|
|
|
![](/images/audio/phono-x/pcb-3d.png)
|
|
|
|
The width of the board was chosen to fit in the pcb brackets of the enclosure.
|
|
|
|
## Retrospective
|
|
|
|
So, what did I learn doing this build?
|
|
|
|
1. There's (presumably) a considerable inrush current into the big `C1-C4` capacitors. When
|
|
the amp is already powered up, switching on the Phono X will cause a not-so-nice popping sound. I should
|
|
probably add some soft
|
|
1. When powering off, the capacitors keep the amp working for quite a while. It might be nicer to
|
|
really shut down the output when turning off.
|
|
1. Transformers affect signals. Keep them away from signal traces or maybe use some sort
|
|
of shielding.
|
|
1. Add the recommended [Project 99 Subsonic Filter](http://sound.whsites.net/project99.htm) to prevent sub 20Hz noise coming through.
|
|
1. Get the right equipment to measure performance of my build myself ;-)
|
|
1. Use a more symetrical design for the PCB, and maybe split the power supply and signal boards into two separate boards.
|
|
|
|
## Datasheets
|
|
|
|
* [OPA2134] High Performance Audio Operational Amplifier
|
|
|
|
[OPA2134]: http://www.ti.com/lit/ds/symlink/opa2134.pdf
|
|
|
|
|
|
|
|
|