Draft: Rotel RB-970BX
This commit is contained in:
parent
f921b5b553
commit
2987b1e24d
71
content/electronics/repair-rotel-rb-970bx.md
Normal file
71
content/electronics/repair-rotel-rb-970bx.md
Normal file
|
@ -0,0 +1,71 @@
|
||||||
|
+++
|
||||||
|
date = "2017-11-06"
|
||||||
|
title = "Repair: Rotel RB-970BX"
|
||||||
|
tags = ["rotel", "repair", "audiorepair"]
|
||||||
|
categories = [ "Audio Repair" ]
|
||||||
|
description = "Another lucky find: Rotel RB-970BX Power Amplifier with one defective channel. Let's fix this!"
|
||||||
|
slug = "repair-rotel-rb-970bx"
|
||||||
|
draft = true
|
||||||
|
+++
|
||||||
|
|
||||||
|
![The Rotel RB-970BX](/img/rotel-rb970bx-front.jpg)
|
||||||
|
|
||||||
|
I did another great find on _Marktplaats_: a Rotel RB-970BX. This is a power amplifier, meaning it has no
|
||||||
|
volume or tone controls whatsoever. You'd normally pair a RC-970BX pre-amp with one or two of these
|
||||||
|
power amplifiers.
|
||||||
|
|
||||||
|
The amp can run in stereo mode at 60 Wpc or in _bridged mono_. In bridged mono you can use the entire
|
||||||
|
amp to amplify _one_ channel and get 180 Wpc. Of course, for stereo, you'd need two of these
|
||||||
|
amplifiers in your setup.
|
||||||
|
|
||||||
|
![Bridged Mono on the RB-970BX](/img/rotel-rb970bx-bridged-mono.png)
|
||||||
|
|
||||||
|
## Diagnostic
|
||||||
|
|
||||||
|
I bought this amp with the remark that one channel did not produce any sound. This could be due
|
||||||
|
to a number of reasons, but most likely one or more components in the circuit will have failed.
|
||||||
|
|
||||||
|
Before testing the amp to determine _which_ channel is not working, I opened up the Rotel and
|
||||||
|
checked for any obvious failures: burnt resistors, exploded or leaking caps, and blown
|
||||||
|
fuses. Besides some oxidation on the mechanical parts and jumpers I could not find anything
|
||||||
|
out of the ordinary.
|
||||||
|
|
||||||
|
![The insides of the RB-970BX](/img/rotel-rb970bx-pcb.jpg)
|
||||||
|
|
||||||
|
After that I did some quick measurements (still with the unit powered off):
|
||||||
|
|
||||||
|
* Check for shorts on the transistors on the heatsinks
|
||||||
|
* Resistance of the bias resistors (the larte white ones)
|
||||||
|
|
||||||
|
Both of these showed that none of the power transistors had shorts, and that all
|
||||||
|
bias resistors were well within spec (0.22Ω).
|
||||||
|
|
||||||
|
Next I powered up the amp for the first time - with nothing connected to it. I measured
|
||||||
|
for DC on the outputs but both were in the mV range, so nothing out of the ordinary
|
||||||
|
there.
|
||||||
|
|
||||||
|
With that I continued to hook up my dummy load and test which channel _if any_ was not
|
||||||
|
functioning. Right was working just fine, but left appeared to be dead as a doornail.
|
||||||
|
|
||||||
|
Because the amp is pretty bare bones, my next step was to test the transistors on the
|
||||||
|
PCB for the left channel. The first one I tested (Q615, a humble 2SC2910 NPN transisor)
|
||||||
|
showed a short between _emitter_ and _base_.
|
||||||
|
|
||||||
|
A quick probe around showed no other damaged parts. So, I ordered a few new 2SC2910's from
|
||||||
|
a local supplier and waited for them to arrive.
|
||||||
|
|
||||||
|
## The Repair
|
||||||
|
|
||||||
|
The repair is as simple as replacing the damaged transistor.
|
||||||
|
|
||||||
|
Since I'm there, I've also cleaned the oxidation from the jumpers and mechanical parst,
|
||||||
|
cleaned the PCB and replace the four capacitors for good measure.
|
||||||
|
|
||||||
|
## Conclusion
|
||||||
|
|
||||||
|
A single failed transistor took out the entire left channel. Replacing a €1 part revived
|
||||||
|
this power amplifier to its former glory.
|
||||||
|
|
||||||
|
## Links
|
||||||
|
|
||||||
|
[Rotel RB-970BX Datasheet at Hifiengine](https://www.hifiengine.com/manual_library/rotel/rb-970.shtml)
|
BIN
static/img/rotel-rb970bx-bridged-mono.png
Normal file
BIN
static/img/rotel-rb970bx-bridged-mono.png
Normal file
Binary file not shown.
After Width: | Height: | Size: 268 KiB |
BIN
static/img/rotel-rb970bx-front.jpg
Normal file
BIN
static/img/rotel-rb970bx-front.jpg
Normal file
Binary file not shown.
After Width: | Height: | Size: 1.7 MiB |
BIN
static/img/rotel-rb970bx-pcb.jpg
Normal file
BIN
static/img/rotel-rb970bx-pcb.jpg
Normal file
Binary file not shown.
After Width: | Height: | Size: 2.2 MiB |
BIN
static/img/~~rotel-rb970bx-front.jpg
Normal file
BIN
static/img/~~rotel-rb970bx-front.jpg
Normal file
Binary file not shown.
After Width: | Height: | Size: 61 KiB |
Loading…
Reference in New Issue
Block a user